收藏本站
DATASHEET
SMD ?B
12-23C/R6GHBHC-A01/2C
 
 
 
11 
opyright ? 2010, Everlight All Rights Reserved. Release Date : 21-May-2013. Issue No: DSE-0005517 Rev.6
www.everlight.com 
 
 
Precautions For Use
 
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30    or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30    or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60 5   for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
P r e - h e a t i n g
1 5 0 ~ 2 0 0 ?nbsp C
6 0 ~ 1 2 0 s e c .
A  b o v e 2 1 7 ?nbsp C  
6 0 ~ 1 5 0 s e c .
2 6  0  ?nbsp C   M   a x  .
1  0  s e c . M   a x  .
6  ?nbsp C  / s e c . M   a x  .
A  b  o  v  e 2  5  5  ?nbsp C  
3  0  s e c . M   a x  .
3 ?nbsp C  / s e c . M  a x .
 
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350    for 3 seconds within once in less than the
soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because
the damage of the product is often started at the time of the hand solder.
 
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering
iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will
not be damaged by repairing.
 
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
1254-10SYGT/S530-E2 LED 3MM ROUND YLW/GRN DIFF
1383SDRD/S530-A3 LED 5MM ROUND DEEP RED DIFF
15-13D/R6GHBHC-A01/2T LED RED/GRN/BLUE WATER CLR 1210
19-137/R6GHBHC-A01/2T LED RED/GREEN/BLU WATER CLR 0603
204-10SURC/S530-A3 LED 3MM HYPER RED WATER CLEAR
204-10SURD/S530-A3 LED 3MM BRILLIANT RED RED DIFF
204-10SURT/S530-A3 LED 3MM HYPER RED RED TRANSFL
204-10SYGT/S530-E2 LED 3MM SUPER YLW-GRN GRN TRANSF
相关代理商/技术参数
12-23C/S2GHBHC-A01/2C 功能描述:标准LED-SMD RGB Water Clear RoHS:否 制造商:Vishay Semiconductors 封装 / 箱体:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明颜色:Red 波长/色温:631 nm 透镜颜色/类型:Water Clear 正向电流:30 mA 正向电压:2 V 光强度:54 mcd 显示角:130 deg 系列:VLMx1500 封装:Reel
12-23CBH 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)
12-23CBH-A01 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)
12-23CBH-A012C 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)
12-23CGH 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)
12-23CGH-A01 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)
12-23CGH-A012C 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)
12-23C-R6GHBHC-A01-2C 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Full Color Chip LED (Chip LED with Right Angle Lens)